List of custom products in the past|YASUDA SEIKI SEISAKUSHO LTD. providing you the best material testing equipment.

No.127 CABTYRE CABLE ABRASION TESTER

JIS C3005

No.127 CABTYRE CABLE ABRASION TESTER

  • This tester is used to conduct an abrading test on rubber and plastic electric insulated wires.
  • One end of the test specimen is to be attached to the 300 mm above the abrading circle and the other end attached with prescript load. The operator is to see if the insulated material inside the coated material appears due to abrasion.

 

 

Specification

Abrasion Wheel φ350 mm, W50 mm Material: CS Grit: #36
Wheel Rotation Speed 60 rpm
Weight Initial 1 kg to Max. 10 kg
Counter 6 Digits Preset Counter
Power Source AC 100 V, 1-Phase, 10 A, 50/60 Hz
Dimensions/ Weight (Approx.) W630 × D450 × H900 mm, 70 kg

No.200 LUPKE TYPE REBOUND RESILIENCE TESTER

JIS K6255, ISO 4662

 

No.200 LUPKE TYPE REBOUND RESILIENCE TESTER

  • This tester is to measure the rebound resilience of vulcanized rubber and thermo-plastic rubber.
  • The iron made pendulum hung from a height of 2,000 mm by 4 hanging wires hits the test specimen horizontally at a height of 100 mm. The rebound resilience can be read to the quotient (1/100).

 

 

 

Specification

Hammer Hemispherical shape, φ12.50 ± 0.05 mm, L356 mm, Mass 0.35 ± 0.01 kg
Impact Speed 1.40 ± 0.01 m/s
Hammer Falling Height 100 mm
Hammer Hanging Height 2,000 mm
Specimen Cylindrical shape, T12.5 ± 0.5 mm, φ29.0 ± 0.5 mm
Clamp Inner φ20 mm, Outer Diameter φ35 mm
Power Source AC 100 V, 1-Phase, 3 A, 50/60 Hz
Dimensions/ Weight (Approx.) W1,460 × D900 × H2,270 mm, 60 kg

Inquiry Form

No.253 ELECTRIC RECIPROCATING ABRASION TESTER (FOR PLUG PIN)

JIS C8282-1, IEC-60884-1

No.253 ELECTRIC RECIPROCATING ABRASION TESTER (FOR PLUG PIN)

  • This tester is used to evaluate the abrasion resistance of insulating sleeve in plug pins by abrading a U-shaped copper wire at a desired abrading speed, length, number, and load.
  • After test completion, the operator is to check whether there is any damage, holes, or wrinkles visible on the test specimen.

 

 

 

Specification

Stroke 1 Left-Max. 100 mm (Length Setting Sensor Attached) (Standard 9 mm), Front-Back Max. 50 mm
Abrading Angle 10°
Abrading Speed 30 times/min
Weight Load 4 N
U-shape Copper Wiring φ1 mm
Accessories Spirit Level
Power Source AC 100 V, 1-Phase, 5 A, 50/60 Hz
Dimensions/ Weight (Approx.) W450 × D300 × H550 mm, 30 kg

Inquiry Form

No.276 HEAT SEAL TESTER

No.276 HEAT SEAL TESTER

  • This tester is used to measure the optimal temperature when sealing cellophane tape, plastic film etc.
  • Setting the sealing pressure and the sealing time identical for the 5 heating platen, the operator can evaluate the thermal adhesion among the 5 different testing temperatures.

 

 

 

Specification

Seal Plate 10 × 25 mm: 5 pcs or 7 pcs (2 kinds)
Temperature Range Max. 200 °C
Pressing Method Pneumatic Cylinder, Stoke Max. 45 mm
Pressure Gauge Max. 0.5 MPa (Scale 0.01 MPa)
Timer Max. 99.99 sec
Accessories Foot Switch
Option Safety Cover, Air Compressor
Power Source AC 100 V, 1-Phase, 15 A, 50/60 Hz
Air Source 0.5 MPa or More
Dimensions/ Weight (Approx.) W760 × D350 × H900 mm, 80 kg (7 pcs)

Inquiry Form

No.316 RING CRUSH TESTER

JIS P8126, ISO 12192(Option: Z0402, Z0403-1, Z0403-2)

No.316 RING CRUSH TESTER

  • This tester is used to evaluate the compressive strength of ring shaped paper board according to the ring crush method.
  • By changing the jig (option), the tester enables to conduct adhesive power test of cardboard, flat surface compression test, and vertical compression test.

 

 

 

Specification

Specimen W12.7 ± 0.1 mm, L152.4 to 2.5 mm, T580 µm or Less
Specimen Holder Outer Frame: Inner Diameter φ49.30 ± 0.05 mm, D6.35 ± 0.25 mm
Inner Frame: 9 kinds (To be Specified)
Load Measuring Load Cell: Max. 1,999 N
Compression Plate 100 × 100 mm
Compression Speed 12.5 ± 2.5 mm/min
Option Pin Attachment, Vertical Compression Jig
Power Source AC 100 V, 1-Phase, 10 A, 50/60 Hz
Dimensions/ Weight (Approx.) Tester Body: W350 × D400 × H540 mm, 60 kg
Control Box: W135 × D350 × H250 mm, 10 kg

Inquiry Form

No.324 CANADIAN STANDARD FREENESS TESTER

JIS P8121, TAPPI-T227, ISO 5267-2

No.324 CANADIAN STANDARD FREENESS TESTER

  • This tester is used to evaluate the freeness of pulp.
  • By filtrating a certain amount of test specimen, the operator is to read the amount of discharged test specimen that flew out from the side tube.
  • The operator is to use the correction table so that the test data is calibrated to the Canadian standard freeness conditions of a standard density of 0.3 % and standard temperature of 20 °C.

 

 

Specification

Specimen Bone-Dried 3 g, Concentration 0.3 %, Solution 1,000 ml
Drainage Chamber Inner Diameter φ101.5 ± 0.4 mm
H127 mm (Wire Screen to Rim)
Air Cock Hole φ4.7 mm or More
Wire Screen φ111.0 ± 0.5 mm, 80 mesh
Measuring Funnel Opening φ204 mm
Overall L280 mm
Bottom Orifice φ3.05 ± 0.01 mm
Side Orifice Inner Diameter φ13 mm
Accessories Measuring Cylinder, Jug
Option Stand
Dimensions/ Weight (Approx.) W300 × D270 × H720 mm/ 22 kg

Inquiry Form

No.325 SCHOPPER-RIEGLER TYPE FREENESS TESTER

JIS P8121, ISO 5267-1

No.325 SCHOPPER-RIEGLER TYPE FREENESS TESTER

  • This tester is used to evaluate the freeness of pulp. By filtrating a certain amount of test specimen, the operator is to read the amount of discharged test specimen that flew out from the side tube to calculate the Schopper freeness.
  • The down flow of the test specimen will be done by pulling up the circular coned valve upwards.

 

 

Specification

Specimen Bone-Dried 2 g, Concentration 0.2 %, Solution 1,000 ml
Drainage Chamber Inner Diameter φ137 mm、H150 mm(Wire Screen to Rim)
Wire Screen φ112.9 ± 0.1 mm, 100 mesh
Measuring Funnel Opening φ115 mm, H150 mm, Bottom Orifice φ2.4 mm
Accessories Measuring Cylinder, Jug
Dimensions/ Weight (Approx.) W250 × D460 × H1,100 mm/ 18 kg

Inquiry Form

No.330 PULP SCREENING TESTER

JIS P8207

No.330 PULP SCREENING TESTER

  • This tester is used to evaluate the fiber length distribution of paper making pulp.
  • The 4 tanks which have different size of metal mesh, screens the test specimen.
  • The operator is to measure the absolute dry mass of pulp in each tank to calculate the screening degree.

 

 

 

Specification

Specime Bone-Dried 10 g, Concentration 1 %, 1,000 ml
Test Bath 191 × 191 × 290 mm
Stirrer Rotation Speed 800 rpm
Water Feed 8.3 L/min
Wire Screen Diameter φ102 mm
Screen Combination 710, 355, 180, 106 µm/
1180, 600, 300, 150 µm/
1400, 850, 600, 300 µm
Option Flow Meter, Timer
Power Source AC 100 V, 1-Phase, 15 A, 50/60 Hz
Dimensions/ Weight (Approx.) W1,350 × D300 × H1,400 mm, 120 kg

Inquiry Form

No.338 AUTOMATIC K.B.B. SIZING TESTER

J.TAPPI-No.13/1, JIS K8122

No.338 AUTOMATIC K.B.B. SIZING TESTER

  • This tester is used to measure the K.B.B. size (water resistance) of paper and paperboard.
  • The operator is to clamp the test specimen into one pair of dissimilar metal and soak the surface of the test specimen with an electrolyte liquid that is at a constant density.
  • The tester will automatically measure the time it took to flow electricity due to the penetration of the electrolyte liquid.

 

 

Specification

Specimen 90 × 90 mm
Moveable Electrode (Anode) Bronze Made
Fixed Electrode (Cathode) Zinc Made, For One Side Penetration, For Both Side Penetration
Micro Current Meter 0 to 100 µm
Timer Max. 99999.9 sec, Digital Display Ver.
Electrolyte Solution Potassium Chloride Solution (1 %)
Power Source AC 100 V, 1-Phase, 3 A, 50/60 Hz
Dimensions/ Weight (Approx.) W400 × D350 × H500 mm, 20 kg

Inquiry Form

No.371-S CARDBOARD CONTAINER COMPRESSION TESTER

JIS Z0212, TAPPI-T804

No.371-S CARDBOARD CONTAINER COMPRESSION TESTER

  • This tester is used to conduct compression test to packaged cargo and container.
  • The tester is especially suitable to evaluate compression strength of packaged cargo when it is lower loaded during its logistic process.

 

 

 

Specification

Maximum Load Max. 30 kN
Compression Plate 1,000 × 1,000 mm
Plate Opening Max. 1,100 mm
Compression Speed 10 ± 3 mm/min
Accessories Chart Recorder
Power Source AC 200 V, 3-Phase, 10 A, 50/60 Hz
Dimensions/ Weight (Approx.) Tester Body: W1,500 × D1,000 × H2,300 mm, 1,200 kg
Control Box: W520 × D400 × H1,200 mm, 70 kg

Inquiry Form

No.601 BELT FATIGUE TESTER

No.601 BELT FATIGUE TESTER

  • This tester is to evaluate the fatigue strength by flexing the steel belt used in tires.
  • The specimen is bent in half and flexed through horizontal movement while being tensioned.

Specification

Hangings 12 Hangings, Single Driving Type
Flexing Length 120 mm
Flexing Speed 165 times/min
Test Load Max. 60 kgf
Temperature Range 0 to 100 °C (Refrigerator)
Power Source AC 200 V, 3-Phase, 30 A, 50/60 Hz
Dimensions/ Weight (Approx.) W1,900 × D950 × H1,850 mm/ 1,000 kg

Inquiry Form

No.602 SUNROOF ADHESIVE SSTRENGTH TESTER

No.602 SUNROOF ADHESIVE SSTRENGTH TESTER

  • This tester is used to evaluate the adhesive strength of sunroof glass and its bonded zone.
  • By pressing the center of Sunroof Glass, the machine measures how much pressure is required to dethatch the glass from its bonded zone.
  • By pressing at a constant pressure, the bonded zone conditions can also be evaluated.

Specification

Sample Size Width: Max. 1,100 mm Length: Max. 900 mm
Load Measurement Load Cell
Press Speed Max. 150 mm/min
Accessories Glass Receiving Pan
Temperature Range 0 to 100 °C (Refrigerator)
Power Source AC 200 V, 3-Phase, 5 A, 50/60 Hz
Dimensions/ Weight (Approx.) W1,600 × D1,000 × H1,250 mm/ 500 kg

Inquiry Form

No.603 FILM FLEX FATIGUE TESTER

No.603 FILM FLEX FATIGUE TESTER

  • This tester is used for evaluating the Flexing Resistance of plastic film and flexible printed circuits.
  • The specimen is attached on both ends and bent at the mandrel, and flexed to the desired angle.
  • This tester is mainly used for evaluating film materials used in folding cell phones.

Specification

Hangings 3 Hangings
Flexing Angle 90°, 120°
Flexing Speed 60 times/min, 120 times/min
Test Load Max. 800 g
Option Low Temp. Chamber, Conduction Device (for FPC)
Power Source AC 200 V, 1-Phase, 15 A, 50/60 Hz
Dimensions/ Weight (Approx.) W600 × D600 × H1,150 mm/ 100 kg

Inquiry Form

No.604 FILM TWIST TESTER

No.604 FILM TWIST TESTER

  • This tester is used for evaluating the twist endurance of plastic film/ flexible print circuit (FPC).
  • The specimen is fixed on both ends and twisted to a certain angle.

Specification

Twist Angle ± 180°
Twist Speed 30 cpm, 60 cpm, 180 cpm
Test Load Max. 200 g
Option Low Temperature Specification, Conduction Device (for FPC)
Power Source AC 100 V, 1-Phase, 10 A, 50/60 Hz
Dimensions/ Weight (Approx.) W300 × D520 × H360 mm/ 20 kg

Inquiry Form

No.650 ELECTRIC RECIPROCATIVE ABRASION TESTER (FOR GULF HEADS)

No.650 ELECTRIC RECIPROCATIVE ABRASION TESTER (FOR GULF HEADS)

  • This tester is used for evaluating the abrasion resistance of gulf heads and their plating.
  • The abrader can be changed along with test conditions (abrading stroke/ abrading speed/ number of strokes/ weight load).

Specification

Abrading Stroke Left-Right Max. 100 mm (with Reciprocate Stroke Sensor),
Front-Rear Max. 110 mm, Inching Feature
Abrading Speed Motorized (Max. 6 mm/s)
Weight Load Max. 1 kgf (Balance Weight)
Accessories Specimen Height Adjuster
Power Source AC 100 V, 1-Phase, 5 A, 50/60 Hz
Dimensions/ Weight (Approx.) W440 × D200 × H500 mm/ 30 kg

Inquiry Form

No.660 AEROSOL SPRAY TESTER

No.660 AEROSOL SPRAY TESTER

  • This tester is for evaluating the effect of the contents of aerosol product when a certain the spraying condition (pressing pressure, pressing stroke, pressing time) is maintained.
  • This is used when spraying insecticides into a container with a certain volume.

Specification

Aerosol Diameter: Max. φ80 mm, Length: Max. 300 mm
Power Source AC 100 V, 1-Phase, 5A, 50/60 Hz
Dimensions/ Weight (Approx.) Main Body: W100 × D100 × H500 mm/ 0.65 kg (Aerosol Not Included)
Control Box: W150 × D100 × H200 mm/ 3 kg

Inquiry Form

No.661 DOOR HANDLE ENDURANCE TESTER

No.661 DOOR HANDLE ENDURANCE TESTER

  • The tester repeatedly opens/ closes the door by pulling and pushing the door knob. Once the door knob breaks, the load cell detects its damage and stops testing automatically.
  • The test chamber temperature can be set by controller between 3 temperature conditions.

Specification

Hangings 1 Hanging
Opening Span 0 to 40 mm
Test Speed 40 times/min
Load Measurement Load cell, Max. 1,000 N
Load Detection 100 N or 500 N (Spring Weight)
Temperature Range -30 to 70 °C (Refrigerator), PID Control
Power Source AC 200 V, 3-Phase, 30 A, 50/60 Hz
Dimensions/ Weight (Approx.) W900 × D1,000 × H1,810 mm/ 700 kg

Inquiry Form

No.662 HINGE CAP ENDURANCE TESTER

No.662 HINGE CAP ENDURANCE TESTER

  • This tester is used for conducting endurance tests on hinge caps used for stationary and medicine containers.
  • Attachment jigs can be custom made to meet various cap shapes.

Specification

Cap Opening Angle 120° (Option: Free Angle)
Opening Speed 50 times/min (Option: Speed Controller)
Option Break Detection Feature
Power Source AC 100 V, 1-Phase, 5 A, 50/60 Hz
Dimensions/ Weight (Approx.) W250 × D365 × H450 mm/ 15 kg

Inquiry Form

No.663 FURNITURE REPETATIVE FORCE ENDURANCE TESTER

JIS S1203

No.663 FURNITURE REPETATIVE FORCE ENDURANCE TESTER

  • This tester is for evaluating the strength and durability of furniture such as chairs or stools.
  • The chair/ stool is fixed and applied a certain amount of weight onto the sitting surface, and the deflection amount and appearance at the sitting surface is recorded.
  • This tester can also be used to check the strength of the handle grips of suitcases, backpacks, and frying pans.

Specification

Load Max. 950 N
Loading Speed Less than 40 Cycles
Loading Stroke 200 mm
Accessories Plummet , Spirit Level
Power Source AC 200 V, 3-Phase, 10 A, 50/60 Hz
Dimensions/ Weight (Approx.) W2,100 × D900 × H1,800 mm/ 450 kg

Inquiry Form

No.664 NAIL PENETRATION TESTER

No.664 NAIL PENETRATION TESTER

  • This tester is used to demonstrate a short-circuit, one cause of accidental combustion, by penetrating lithium-ion batteries.
  • By penetrating the separators within batteries which sustain insulation, a short circuit is created.
  • The test is conducted to examine the results by comparing penetrating conditions such as depth, speed, nail size and materials.

Specification

Depth Max. 10 mm
Speed 0.2, 2, 20 mm/sec
Nail Size Max. φ4.0 mm
Power Source AC 100 V, 1-Phase, 5 A, 50/60 Hz
Dimensions/ Weight (Approx.) W530 × D400 × H710 mm/ 50 kg

Inquiry Form

Inquiry Form

    Catalog No. or Product Name*

    Request*

    Motive*

    Company Name*

    *Please input as much information as possible.

    Department

    First name*

    Last name*

    ZIP Code*

    Country*

    Address*

    Telephone Number*

    E-Mail Address*

    Description*